Search:

Type: Posts; User: Aerocoupe

Page 1 of 14 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    3
    Views
    1,310

    http://www.foxtbirdcougarforums.com/ These...

    http://www.foxtbirdcougarforums.com/

    These guys can help you out in no time.
  2. Sold on www.69stang.com for asking price and...

    Sold on www.69stang.com for asking price and shipping.
  3. F/S: Painless Wiring 5.0L Ford Wiring Harness 86-93, P/N 60510 & A9L EEC

    I have a brand new in the box Painles Wiring harness for the 5.0L Ford 86-93 that comes with an A9L EEC. The A9L is 100% stock and still has the tamper tape on the service port where a programmer or...
  4. Bump.

    Bump.
  5. Replies
    18
    Views
    2,869

    I had synthetic bushings in my control arms and...

    I had synthetic bushings in my control arms and hated them. Pulled the car back apart that same week and installed Moog bushings and drove the shit out of it for several years with zero issues. The...
  6. Replies
    50
    Views
    7,432

    Zero side to side movement however the arc in...

    Zero side to side movement however the arc in which the rear end travels is different. I have 275/40/17's on the rear of the Coupe and it has a 95-98 width rear end. I had to really massage the...
  7. Replies
    19
    Views
    43,179

    Good site for the Fox Birds and Cougars: ...

    Good site for the Fox Birds and Cougars:

    http://www.foxtbirdcougarforums.com

    Darren
  8. Replies
    50
    Views
    7,432

    I ran my Coupe with MM LCA's, one stock UCA with...

    I ran my Coupe with MM LCA's, one stock UCA with stock rubber bushings (you do not install anything but rubber bushings), and a MM panhard bar with no issues. The car had conventional coil springs...
  9. Auto Meter Oil Pressure, Water Temperature, and Fuel Pressure Gauges For Sale

    I have the following 2-5/8" Auto Meter gauges out of my T-Bird for sale:

    (1) Autometer Sport Comp 3521 (silver bezel black face) 0-100 psig oil pressure gauge (electric) with sender & fittings,...
  10. Replies
    9
    Views
    1,847

    If you are worried about it just clip the loop...

    If you are worried about it just clip the loop off the wires that go to the back of the alt and heat shrinked the ends. Run the fused 4 ga from the back of the alternator over to the starter...
  11. Replies
    9
    Views
    1,847

    Go here: ...

    Go here:

    http://351winsor.com/joel/EEC-IV/90_Wire_Diag_1.JPG

    Darren
  12. Replies
    26
    Views
    2,510

    Is it the same block the dizzy came out of? ...

    Is it the same block the dizzy came out of?

    Darren
  13. Replies
    1
    Views
    863

    Should be a 194 part number. Darren

    Should be a 194 part number.

    Darren
  14. Replies
    13
    Views
    1,446

    I believe the instructions for the FRPP balancer...

    I believe the instructions for the FRPP balancer give the interference fit range and say to preheat it before installation. See here:
    ...
  15. Replies
    13
    Views
    3,240

    Are you sure your tailpipes are not rubbing on...

    Are you sure your tailpipes are not rubbing on the control arms that you just replaced? They may clear them with the car sitting normally but under a load and in a turn they may be hitting something...
  16. Replies
    3
    Views
    601

    You will need to post the model number off the...

    You will need to post the model number off the MAF element to get that information. I think you can even search it on their site.

    Darren
  17. Replies
    3
    Views
    601

    You can send it back to Pro-M: ...

    You can send it back to Pro-M:

    http://www.promracing.com/meter-recalibration-repair.html

    What you need to do is look at the elements on the MAF and make sure they are good to go. If one of them...
  18. Replies
    2
    Views
    1,402

    Have you tried a Haynes manual? Mine shows all...

    Have you tried a Haynes manual? Mine shows all the wire colors and connectors for my 93. I checked Autozone and they looked pretty decent to me:
    ...
  19. Sold. Darren

    Sold.

    Darren
  20. Replies
    6
    Views
    4,297

    Nitrous Works used to make one but they are out...

    Nitrous Works used to make one but they are out of business now (I believe they were associated with Barry Grant and folded when they did). You may get lucky and score a used one.

    Darren
  21. Replies
    12
    Views
    1,163

    Typically the Ford dealer has them and any glass...

    Typically the Ford dealer has them and any glass shop will have them as the windows are rivited into the lift with the same style of rivit but they are a bit longer but will work for the door handles...
  22. TTT. Darren

    TTT.

    Darren
  23. Bump. Darren

    Bump.

    Darren
  24. Replies
    3
    Views
    658

    I would not sand blast those covers as they are...

    I would not sand blast those covers as they are waaay too thin. I would look at bead blasting them as it is much more forgiving and does not build the heat and the tendency to warp thin metal like...
  25. F/S: 79-93 One-Piece Black Radiator Hold Down

    I bought this for my T-Bird when I had a mechanical fan on it but with the Mark VIII fan I decided to fabricate my own. I pulled it off the car this past weekend and would take $30.
    ...
Results 1 to 25 of 344
Page 1 of 14 1 2 3 4